Car Performance Specs

1. Place the BMW’s transmission into Park (automatic) or neutral (manual transmission) and apply the parking brake. Leave the engine running.
2. Connect a scan tool to the BMW’s diagnostic data port, which is under the dashboard just above the pedals on the driver’s side.
3. Power on the scan tool and choose “Bi-Directional Tests” from the main menu. Select “IAC Valve Actuation” from the tests menu.
4. Use the scan tool’s buttons to open and close the IAC valve. The idle speed should rise and lower without pressing the accelerator. If the IAC valve does not respond to the scan tool by raising and lowering the engine idle speed, then it is faulty.

1. Disconnect the negative terminal on the battery. Ensure that you have the code for your radio if it is the OEM stereo, since disconnecting the battery resets it.
2. Remove the Torx screws that hold the instrument cluster to the dash pod with a T20 Torx bit and a ratchet.
3. Protect the plastic on the gauge panel with a piece of flannel. Also lay a heavy towel on the steering column to offer more protection.
4. Slide a very thin tool (feeler gauge, thin spatula, etc.) between the cluster and the gauge pod on the edge near the center of the car. Very gently pry the cluster out far enough so that you can access the wires on the back of it.
5. Disconnect the three electrical connectors that go to the back of the cluster. The connectors are released by pressing the tabs down where they connect and pulling the wires out. Move the cluster to your workbench and lay it on a soft towel.
6. Replace the two odometer bulbs by turning and pulling them out of the instrument cluster and installing the new ones. Use a small screwdriver to help twist in the new bulbs. The odometer bulbs are beige. All of the other bulbs are black.
7. Place the instrument cluster back in the dash pod and connect the three electrical connectors. Carefully slide the cluster back into place and tighten the two Torx bits. Enter the radio code if needed and reset the clock.

Automobiles are essentially built to serve a purpose, to facilitate transport from one point to another. They are machines manufactured solely to perform their function. However, for most people, a car is more than just a machine but a work of art as well. Consider a BMW, with its solid engineering, sleek lines and exceptional quality and you will see a marriage of art and technology. A BMW commands respect in the automotive world. Renowned for its innovative engineering and technology, a BMW is made to perform. There is a reason why a BMW is called the "Ultimate Driving Machine". It is because the BMW experience elevates driving to the level of pure pleasure.

Yet, there is more to the BMW than its legendary engineering, responsiveness, precision and agility. A good look at any BMW and anyone can understand why these vehicles have captured the hearts and minds of many car lovers through the years. A BMWs design is classic and timeless, with clean, sleek lines and distinct details. BMW is always forward-looking in its designs. It has established a standard, which other carmakers follow. Because of the BMWs excellent design quality, it has earned a special place in the hearts of car lovers all over the world.

Car lovers also enhance the looks, elegance and functionality of their BMWs by customizing their vehicles. Car customization is a good way for the car owner to express his individuality and personality through his car. However, creating a completely new look for a BMW or any car can be very expensive. There are a many customization parts and accessories available. The possibilities are endless as to what appearance your BMW can take. It is only limited by the imagination. Body kits, spoilers, wings, decals, bumpers and other accessories are commonly used to customize a car.

However, an easy and economical way to customize a BMW without spending too much is by installing a new set of BMW wheels or BMW hubcaps. BMW wheels, like all BMW Parts, are engineered according to the highest standards. Nevertheless, these factory wheels are similar to thousands of other BMW wheels. Thus, you can introduce a sharper and sportier image to your BMW by installing a new set of good-looking Hubcaps. They are easy to find in the auto parts market and there are dozens of design options. Hubcaps and wheels are common auto products available in auto parts stores.

1. Loosen the lug nuts on both front wheels by turning them 1/4 turn counterclockwise.
2. Raise the BMW up using the floor jack. Jack under the front jack point.
3. Place jack stands underneath the pinch welds of the BMW and lower the vehicle onto the jack stands.
4. Finish loosening the lug nuts and take the wheel off.
5. Unbolt the top and bottom brake caliper mounting bolts on the BMW and secure the caliper to the coil spring above the brake assembly with the zip ties.
6. Remove the brake pads by taping them out with a rubber mallet.
7. Place the face of the brake pad over the caliper piston and then place the c-clamp over the back of the brake pad and caliper assembly. Gently force the caliper piston back into the caliper by tightening the c-clamp.
8. Insert the new pads and reassemble the brake system. Installation is the reverse of removal.
9. Repeat steps 4 - 8 with the other front wheel.
10. Put the wheels back on, tighten the lug nuts and lower the vehicle. Torque the lug nuts to 100 foot-lbs once the wheel is back on the ground.
11. Raise the rear of the BMW using the rear jack point and place the jack stands under the pinch welds in the rear of the vehicle.
12. Lower the vehicle onto the jack stands and then repeat steps 4 - 8 for the rear wheels.
13. Put the wheels back on, tighten the lug nuts, and lower the rear of the vehicle. Then, tighten the lug nuts to 100 foot-lbs.

1. Above the radio, locate the symbol or drawing on the button that resembles a windshield. Once you have located the button push it and it should illuminate. In models from the early 90s to 1999 there will be a knob. In the 2000-2008 models, there will be a button.
2. Once you push the button, you have activated the windshield defrost option. In models from the early 90s to 1999 you will have a knob. In this case point the line on the knob towards the symbol of the windshield.
3. Once you do this, find the dial that shows the temperature of the desired air flow. With this feature, you can control the desired temperature, whether you need warm or cold air to blow on the windshield.
4. Locate the button or knob that is used to control the level of the airflow. Again, this will depend on the year of BMW. Adjust the level of airflow that you desire. You will see any fog on the window start to dissipate rapidly. If it does not start to evaporate, try using the opposite temperature that is blowing.
5. Turn the dial to the color blue which represents cold air. Any fog that is on the window should evaporate. If the problem persists, spin the dial to red. This will make warm air flow through the vents, and should solve the problem
6. problem.

So what is 2011 BMW really all about? The following report includes some fascinating information about 2011 BMW info you can use, not just the old stuff they used to tell you.

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

2011 BMW Car

1. Open the hood and unscrew the mounting screws on the backside of the BMWs headlight assembly.
2. Pull the headlight assembly forward.
3. Unplug the halogen power connector from the headlight ballast.
4. Turn the headlight counterclockwise and pull the headlight out of the back of the headlight housing.
5. Insert the HID bulb into the headlight housing assembly. Align the tabs on the headlight with the notches in the headlight housing.
6. Plug the electrical connector from the HID converter ballast into the HID bulb ballast.
7. Plug the factory halogen electrical connector into the back of the HID converter ballast. Your BMW is now set up for HID headlights. The converter ballast will use your factorys headlight wiring to power the HID bulbs.

1. Locate the motorcycle registration or title. Obtain the key code if available. Make sure the paperwork displays your VIN number.
2. Verify the vehicle identification number (VIN) to that on the bike. The VIN is located on the right hand side of the steering head.
3. Bring your drivers license, registration and key code to the closest BMW Motorrad dealers parts department to request a replacement key.

1. Press your fingers against the back side of the side turn signal indicator cover, and push forward. The cover will slide off, exposing the bulb beneath.
2. Grasp the bulb with your fingers, and turn it counterclockwise. Pull the bulb out to remove it. Discard the old bulb.
3. Insert a new, five-watt W5W bulb, and turn it clockwise.
4. Replace the turn signal indicator cover, and press your fingers against the front side of the cover to lock it in place. Replace the other side turn signal indicator, if necessary.

1. Use a wrench to loosen and remove the negative battery terminal. This ensures that no electricity is going to the stereo system while you are working.
2. Use the trim removal tool to pry the trim away from the dash, starting with the area above the glovebox. Slowly work your way toward the trim above the stereo. Remove the trim piece. If you do not have a trim removal tool, wrap electrical tape around the tip of a flat-head screwdriver to remove the trim.
3. Pry up and remove the trim piece above the stereo.
4. Remove the screws on each side of the stereo using the screwdriver, then pull the stereo out from the dash.
5. Press the tab to release the large black connector and remove it from the back of the stereo.
6. Press a flat-head screwdriver against the blue tab on the connector and pry it upward to release the smaller connectors.
7. Insert the gray connector from the "AUX" input kit into the empty portion of the black connector, then replace the other connectors and lock the blue tab back into place.
8. Thread the other end of the "AUX" cable into the opening in the dash and down through the back of the dash so that it comes out in the floor area of the passenger side.
9. Insert the stereo back into the dash and replace the two screws, then replace the trim pieces. Reconnect the negative terminal on the battery.
10. Plug one end of the 3.5mm cable into the "AUX" input jack and the other end into your audio device. Turn on the stereo and select “AUX” as the input type. You should now hear the audio from your device coming through the speakers.

1. Put the key into the ignition and turn the vehicle to the on position but dont start the engine.
2. Find the diagnostic port under the drivers side dashboard near the pedals. Plug the computerized scan tool into this port. The battery from the vehicle will automatically power on the tool.
3. Find arrows on the faceplate of the scan tool and use them to scroll through the menu until you find the Read All Codes command. Select this command.
4. Scroll through the menu again and find Clear All Codes. Select this option then wait for the service engine light to shut off.
5. Turn off the vehicle and wait five minutes. Start the engine and verify that the check engine light is still off.

1. Gather all the supporting evidence you may need. If you sold your vehicle, you will need a copy of your bill of sale. If your car was written off in a car accident; you will need proof from your insurance company.
2. To cancel a dealership-issued warranty, deal with the dealerships finance manager. To cancel the original owner protection plan deal directly with BMW North America, call the necessary provider and get details regarding exactly how to cancel the plan; as each warranty plan has different terms and conditions.
3. For the original owner protection policy, BMW North America requires a reason for cancellation and a written letter detailing the cancellation or transfer. Prepare a signed letter, attach a copy of your proof, and mail directly to BMW North America.

1. Call your BMW lease-end relationship consultant at (800) 959-4BMW (4269) to arrange and negotiate a short-term re-lease. You may re-lease for a minimum of one year and a maximum of three years.
2. Talk to your lease-end relationship consultant about the payment and terms of your re-lease. BMW Financial Services will determine a new lease payment within about 30 days out from your current lease maturity date.
3. Sign the new re-lease agreement to keep a lease on the BMW you are driving if you are satisfied with the terms.

1. Disconnect the negative battery terminal first using a wrench. Engage the parking brake. Slide a drain pan underneath the gas tanks drain plug, before removing the plug and allowing all of the gas to drain out.
2. Remove the bottom seat cushion, then remove the covers on either side of the seat. Raise the rear of your car with a jack, placing a the car onto a pair of support stands. Detach the rear muffler section and driveshaft before attempting to remove the gas tank. To do this you will have to loosen the bolts holding the various components (ie. driveshaft and rear muffler section) into place. Spraying some penetrating oil onto the bolts may make it easier to remove them.
3. Detach all fuel lines connected to the tank using a specialized BMW fuel line removal tool you can find at most auto parts stores. Place another jack beneath the tank as you remove the straps holding the tank in place. The straps are secured with bolts on each end, which you will have to loosen with a socket wrench. Once youve removed all the straps and bolts, the tank will drop onto the jack.
4. Detach all fuel lines, filler hose and fuel pump from the tank while it sits on the jack. Perform any necessary repairs or replace the tank by reversing the previous steps. Finally, lower the car from the support stands and refill the gas tank.

1. Open the door and remove the bottom seat cushion from the car using the 3/8-inch ratchet, extension and sockets. Unbolt the covers located on both sides of the area underneath the seat using the ratchet.
2. Unbolt the fuel level senders on the sides of the tank using the ratchet. Then lift the rear of the car using the jack and set it down onto a pair of jack stands.
3. Unbolt the rear muffler section from the car using the 3/8-inch ratchet, extension and sockets, then lower it out of the way. Unbolt the driveshaft from the rear end of the car using an open-end wrench.
4. Place the jack underneath the gas tank. Unbolt the gas tank from the chassis using the 3/8-inch ratchet, extension and sockets. Slowly lower the jack to drop it down from the chassis. Disconnect the fuel lines and connections from the tank using a flat head screwdriver.

1. Close all of the doors on your car, including the trunk and the hood. Remove your key from the ignition.
2. Open the trunk and then get in the car. Close the drivers door and put the key in the ignition.
3. Turn the key one click to the right, then back to the off position. Repeat this process quickly five times, ending in the off position. This process must be completed in 10 seconds. If successful, you will hear a beep.
4. Open and close your drivers door and press any button on your remote to begin the programming process. The red light on your remote will flash on and off.
5. Open your drivers door and get out of the car to close the trunk. Close the drivers door and wait for the keyless remote to emit another short beep. The programming is now complete.